![\"Consejos](\"http:\/\/arkiplot.com\/arkiplotblog\/wp-content\/uploads\/2014\/12\/erroresT3000.jpg\")
<\/p>\n<\/p>\n
<\/p>\n
A continuaci\u00f3n listamos los errores presentes en el libro de mantenimiento de los plotters Epson SureColor SC-T3000\/T5000\/T7000<\/strong> y que iremos actualizando con nuestras recomendaciones en base a experiencias propias y con clientes.<\/strong><\/p>\n Con esta \u00abbase de datos\u00bb, queremos ayudar a usuarios de impresoras gran formato a solucionar cualquier problema o incidencia que surga con su m\u00e1quina. Aunque en muchos casos la aver\u00eda es solucionable por el usuario, en otros casos ser\u00e1 inevitable la presencia de un t\u00e9cnico especializado. Por ello no podemos dejar de advertir que cualquier intervenci\u00f3n en la impresora conllevar\u00e1 un riesgo que el usuario deber\u00e1 asumir.<\/p>\n <\/p>\n <\/p>\n\n\n
\n 0001<\/td>\n NMI error
\nCPU detects NMI<\/td>\nReplace the MAIN BOARD.<\/td>\n<\/tr>\n \n 0002<\/td>\n System error<\/td>\n Replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 1101<\/td>\n CR life error
\nCR scan pass counter has reached the specified value. (which means the INK TUBES have reached the end of their service life.)<\/td>\nReplace the INK TUBES and reset the counter of the INK TUBE .<\/td>\n<\/tr>\n \n 1125<\/td>\n CR HP detection error
\nThe CR HP SENSOR cannot detect the CR UNIT. Or the CR UNIT cannot detect the touching surface for the home position setting, so the home position cannot be set. \u2022 CR HP SENSOR failure \u2022 False detection of the home due to paper jam or any other obstacle \u2022 Misreading of CR SCALE \u2022 CR Lock is damaged.<\/td>\n1. Replace the CR HP SENSOR. 2. Re-install the CR ENCODER. If it is faulty, replace it. 3. Clean the CR SCALE using ethanol. 4. Replace the CR SCALE. 5. Replace the CR Lock .<\/td>\n<\/tr>\n \n 1138<\/td>\n Over current error
\nConnection failure of the CR MOTOR or the CR ENCODER. \u2022 The number of occurrences of overcurrent to the CR MOTOR has reached a predetermined limit. \u2022 Irregular load \u2022 CR ENCODER failure \u2022 CR MOTOR failure<\/td>\n1. Replace the CR ENCODER. 2. Replace the CR MOTOR.<\/td>\n<\/tr>\n \n 1139<\/td>\n Oscillation error
\nThe control terminal (Vre terminal) of the CR MOTOR driver has shorted out.<\/td>\n1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 113A<\/td>\n Overload error
\nOvercurrent to the CR MOTOR was detected. \u2022 CR ENCODER cable is damaged. \u2022 CR MOTOR cable is damaged. \u2022 Irregular load \u2022 CR ENCODER failure \u2022 CR MOTOR failure<\/td>\n1. Re-install the CR UNIT. 2. Replace the CR ENCODER. 3. Replace the CR MOTOR.<\/td>\n<\/tr>\n \n 113B<\/td>\n Over speed error
\nThe CR MOTOR was driven at a speed faster than a predetermined one during deceleration. \u2022 Irregular load \u2022 CR ENCODER failure \u2022 SUB BOARD is damaged. \u2022 CR MOTOR driver failure<\/td>\n1. Replace the CR ENCODER. 2. Replace the SUB BOARD. 3. Replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 113C<\/td>\n Reversing error
\nThe number of occurrences of reversing the CR MOTOR has reached a predetermined limit. \u2022 The polarity of CR ENCODER cable is opposite. \u2022 The polarity of CR MOTOR cable is opposite. \u2022 Slipping of the teeth of CR TIMING BELT \u2022 CR ENCODER failure<\/td>\n1. Adjust the tension of the CR TIMING BELT. 2. Replace the CR ENCODER.<\/td>\n<\/tr>\n \n 113D<\/td>\n Driving time-out error
\nAbnormally-long driving duration of the CR MOTOR was detected. \u2022 Irregular load \u2022 Firmware becomes out of control.<\/td>\nReplace the MAIN BOARD.<\/td>\n<\/tr>\n \n 113E<\/td>\n Velocity deviation error
\nThe CR MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. \u2022 Irregular load \u2022 CR ENCODER failure \u2022 CR MOTOR failure \u2022 SUB BOARD is damaged. \u2022 CR MOTOR driver failure<\/td>\n1. Replace the CR ENCODER. 2. Replace the CR MOTOR. 3. Replace the SUB BOARD. 4. Replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 113F<\/td>\n Lock error
\nThe CR MOTOR was driven at a speed abnormally slower than a predetermined one during operation. \u2022 CR ENCODER cable is damaged. \u2022 CR MOTOR cable is damaged. \u2022 Irregular load \u2022 CR ENCODER failure \u2022 CR MOTOR failure<\/td>\n1. Replace the CR ENCODER. 2. Replace the CR MOTOR.<\/td>\n<\/tr>\n \n 1219<\/td>\n Oscillation error
\nThe control terminal (Vre terminal) of the PF MOTOR driver has shorted out.<\/td>\n1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 122A<\/td>\n Overload error
\nOvercurrent to the PF MOTOR was detected. \u2022 PF ENCODER cable is damaged. \u2022 PF MOTOR cable is damaged. \u2022 Irregular load \u2022 PF ENCODER failure \u2022 PF MOTOR failure<\/td>\n1. Replace the PF ENCODER. 2. Replace the MAIN BOARD.<\/td>\n<\/tr>\n \n 122B<\/td>\n Over speed error
\nThe PF MOTOR was driven at a speed faster than a predetermined one during deceleration. \u2022 PF irregular load \u2022 PF ENCODER failure \u2022 SUB-B BOARD is damaged. \u2022 PF MOTOR driver failure<\/td>\n1. Replace the PF ENCODER. 2. Replace the SUB-B BOARD. 3. Replace the MAIN BOARD.<\/td>\n<\/tr>\n \n \u00a0154A<\/td>\n Overcurrent to the cutter motor was detected.
\n– Cutter motor encoder cable is damaged.
\n– Cutter motor cable is damaged.
\n– Irregular load
\n– Cutter motor encoder failure
\n– Cutter motor failure<\/td>\nReplace the cutter motor\/cutter
\nmotor encoder (CUTTER UNIT). Consejo Arkiplot<\/strong>: Se recomienda revisar y limpiar -con cuidado- la unidad de corte. Revisar que el mecanismo no est\u00e9 obstruido.<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\nArt\u00edculos y noticias relacionadas:<\/h3>